Tajima
122 cited fault codes · owned by FaultDesk.
| Code | Title | Severity | Confidence | Citations |
|---|---|---|---|---|
| 01 | No 500 character function code when data set is set | stop | verified | 1 |
| 02 | Tajima tape complement error. ( The same +/-- numerics are entered… | stop | verified | 1 |
| 03 | Data is involved in the tape end code | stop | verified | 1 |
| 04 | Improper function code position. Or, wrong tape format was selected | stop | verified | 1 |
| 06 | Memory writing error | stop | verified | 1 |
| 08 | PTR tape signal trouble | stop | verified | 1 |
| 09 | PTR motion is in disorder. Reader does not read the tape for more… | stop | verified | 1 |
| 11 | Data set incomplete | stop | verified | 1 |
| 12 | Excessive stitch back | stop | verified | 1 |
| 13 | Prohibited forward ( When offset is set) | stop | verified | 1 |
| 16 | Tape format 5 is selected although no designs are stored in memory | stop | verified | 1 |
| 17 | After 30 designs have been stored in memory, tape format 2, or 4… | stop | verified | 1 |
| 18 | After the data setting, the number of that design is erased | stop | verified | 1 |
| 19 | Memory capacity shortage during editing | stop | verified | 1 |
| 1B1 | Stop due to frame stepping code | stop | verified | 1 |
| 1B2 | Stop due to stop code | stop | verified | 1 |
| 1B3 | Stop due to end code 1 | stop | verified | 1 |
| 1B4 | Stop due to thread trimming code | stop | verified | 1 |
| 1B5 | Stop due to a sequin code | stop | verified | 1 |
| 1B6 | Stop due to automatic free setting offset code | stop | verified | 1 |
| 1C1 | Stop occurred because bar switch was pressed during frame stepping | stop | verified | 1 |
| 1C2 | Stop by manual ATH operation | stop | verified | 1 |
| 1D1 | Stop at the start of all-head embroidery due to the stop setting | stop | verified | 1 |
| 1D2 | Stop by preset halt | stop | verified | 1 |
| 211 | A fixed position signal is not detected. Main shaft Z signal | stop | verified | 1 |
| 212 | Needle bar is in lowering position | stop | verified | 1 |
| 221 | The frame has traveled left, exceeding the position set by the… | stop | verified | 1 |
| 222 | The frame has traveled right, exceeding the position set by the… | stop | verified | 1 |
| 223 | The frame has traveled up, exceeding the position set by the frame… | stop | verified | 1 |
| 224 | The frame has traveled down, exceeding the position set by the… | stop | verified | 1 |
| 225 | Travel outside the set embroidery area | stop | verified | 1 |
| 226 | Absolute origin limit (+X, -Y) detected | stop | verified | 1 |
| 228 | Table up/down operation was attempted although the frame was in… | stop | verified | 1 |
| 234 | Faulty laser unit | stop | verified | 1 |
| 242 | M-axis rotation range exceeded | stop | verified | 1 |
| 251 | Low oil in the auto lube pump | stop | verified | 1 |
| 252 | The status of the air valve (vacuum) does not change | stop | verified | 1 |
| 253 | Lower limit of the laser protect cover is not detected | stop | verified | 1 |
| 254 | Upper limit of the laser protect cover is not detected | stop | verified | 1 |
| 255 | A peripheral device is defective | stop | verified | 1 |
| 272 | Manual nipple lifting is performed during coiling embroidery | stop | verified | 1 |
| 281 | Target needle position not detected | stop | verified | 1 |
| 291 | Upper thread Breakage is detected. Tension base card is faulty | stop | verified | 1 |
| 293 | Under thread breakage is detected | stop | verified | 1 |
| 2B1 | No response from serial device | stop | verified | 1 |
| 2B2 | TAJIMA code complement error. Same + and | stop | verified | 1 |
| 2B3 | Data exists in an end code | stop | verified | 1 |
| 2B4 | Code format error (A stitch code does not exist at the third… | stop | verified | 1 |
| 2B5 | Reading error, stitch data over 5.1 mm | stop | verified | 1 |
| 2B6 | The serial interface is not ready | stop | verified | 1 |
| 2B7 | The machine was started or frame forward was performed although… | stop | verified | 1 |
| 2B8 | When the pre-reading buffer becomes empty | stop | verified | 1 |
| 2B9 | Memory write error | stop | verified | 1 |
| 2C1 | The machine is started or frame forward/back is executed during… | stop | verified | 1 |
| 2C2 | ON is set for both boring and laser unit) | stop | verified | 1 |
| 2C3 | "Pack" is not designated | stop | verified | 1 |
| 2C4 | The design stitch count is exceeded | stop | verified | 1 |
| 2C5 | An attempt was made to carry out laser processing during laser… | stop | verified | 1 |
| 2C6 | Machine operation was attempted, although the bobbin changer was… | stop | verified | 1 |
| 2D1 | Initial setting of laser power is not complete | stop | verified | 1 |
| 2E3 | Power supply has been interrupted during embroidery | stop | verified | 1 |
| 30 | Stop command by bar switch is given during execution of mode 5, 6,… | stop | verified | 1 |
| 31 | Stop command by bar switch is given during color change | stop | verified | 1 |
| 311 | Encoder A signal status does not change for 5 seconds. Motor or… | stop | verified | 1 |
| 312 | Encoder z signal status does not change for 5 seconds | stop | verified | 1 |
| 313 | Clutch stopper disengaged | stop | verified | 1 |
| 314 | Main shaft rotation failure | stop | verified | 1 |
| 316 | A main shaft driver error is detected | stop | verified | 1 |
| 317 | The take-up lever clutch has received an abnormal signal | stop | verified | 1 |
| 321 | PMD failure | stop | verified | 1 |
| 322 | An X-axis pulse motor driver error signal is detected | stop | verified | 1 |
| 323 | A Y-axis pulse motor driver error signal is detected | stop | verified | 1 |
| 324 | Frame feed output when the needle penetrates the fabric | stop | verified | 1 |
| 325 | Absolute origin could not be detected on the X or Y axis. Cap… | stop | verified | 1 |
| 32A | Hidden Error, usually occurs when the ATH functions | stop | verified | 1 |
| 32F | Hidden Error | stop | verified | 1 |
| 331 | Bobbin Changer error | stop | verified | 1 |
| 341 | An M-axis base point signal is not detected | stop | verified | 1 |
| 342 | An M-axis PMD abnormal signal is detected | stop | verified | 1 |
| 345 | The M-axis clutch driver has received an abnormal signal | stop | verified | 1 |
| 346 | The zig-zag PMD has received an abnormal signal | stop | verified | 1 |
| 347 | An M-axis PMD abnormal signal is detected | stop | verified | 1 |
| 352 | The sequin driver has issued abnormal signals | stop | verified | 1 |
| 371 | Either an upper or lower position signal cannot | stop | verified | 1 |
| 372 | The nipples do not move more than 1 second | stop | verified | 1 |
| 373 | The nipple position sensor issued an abnormal signal | stop | verified | 1 |
| 374 | Nipple sensor signal abnormality, both inputs have signals | stop | verified | 1 |
| 375 | The Z-axis driver (Z-axis release solenoid) has received an… | stop | verified | 1 |
| 381 | FX head needle position input error | stop | verified | 1 |
| 382 | The needle position signal status during color change does not… | stop | verified | 1 |
| 383 | Incorrect input of needle position | stop | verified | 1 |
| 384 | Control error of the looper shaft drive | stop | verified | 1 |
| 385 | Lens does not move to the designated position when during lense… | stop | verified | 1 |
| 391 | Thread release input signal error | stop | verified | 1 |
| 3A1 | The thread trimming driver has issued abnormal signals | stop | verified | 1 |
| 3A2 | Thread trimming output time exceeded | stop | verified | 1 |
| 3A6 | ATH movable knife retract position | stop | verified | 1 |
| 3A8 | A thread holding driver error signal is detected | stop | verified | 1 |
| 3B5 | Communication error in the controller | stop | verified | 1 |
| 3B6 | Communication problem | stop | verified | 1 |
| 3C1 | Power switched on while bar switch was held | stop | verified | 1 |
| 3D1 | There is abnormality in a battery backup signal | stop | verified | 1 |
| 3D2 | There is abnormality in a battery backup signal | stop | verified | 1 |
| 3D3 | There is abnormality in a battery backup signal | stop | verified | 1 |
| 3D4 | A ROM data check sum is abnormal | stop | verified | 1 |
| 3D5 | There is an abnormality in the RAM data checksum | stop | verified | 1 |
| 3D6 | There is abnormality in the program or CPU card The software is… | stop | verified | 1 |
| 3D7 | There is abnormality in the main shaft motor speed control data | stop | verified | 1 |
| 3E2 | The p24R power supply is abnormal | stop | verified | 1 |
| 3F1 | Thread tension control failure | stop | verified | 1 |
| 3F2 | Improper tension (tightness) error | stop | verified | 1 |
| 3F3 | The thread tension release driver has received an abnormal signal | stop | verified | 1 |
| 51 | No stop position signal is output | stop | verified | 1 |
| 52 | Frame limit switch activated | stop | verified | 1 |
| 53 | Stepping motor driver trouble (X, Y) | stop | verified | 1 |
| 54 | Left and right limits on the color change are detected | stop | verified | 1 |
| 55 | Color change takes over 5 seconds | stop | verified | 1 |
| 56 | Color change, half-turn cam signal trouble | stop | verified | 1 |
| 57 | Needle position signal trouble | stop | verified | 1 |
| 58 | One turn of the main shaft motor takes over 5 seconds | stop | verified | 1 |
| 59 | The cap frame moves more than 75mm from the cap frame zero point… | stop | verified | 1 |
| 60 | The embroidery space of the cap frame is exceeded | stop | verified | 1 |